December 05, 2025 10:09 am
« previous next »
Pages: 1 ... 12 13 [14] 15 16 ... 20   Go Down

Author Topic: sko_ford's A mod  (Read 176621 times)

0 Members and 1 Guest are viewing this topic.

Offline sko_ford

  • Suedes Member
  • Traditionalist...or...I post to much.
  • *
  • Posts: 2166
  • Karma: +0/-0
  • Gender: Male
    • View Profile
have you hugged your drill press today
« Reply #195 on: February 19, 2010 10:02 pm »
1540 sworles 3 hrs
Logged
WANTED: Mel Tillis valve covers

Offline boristheblade

  • Street Rodder
  • *
  • Posts: 112
  • Karma: +0/-0
    • View Profile
RE: have you hugged your drill press today
« Reply #196 on: February 20, 2010 3:35 am »
Wood dowel with rubbing compound?
Logged

Offline sko_ford

  • Suedes Member
  • Traditionalist...or...I post to much.
  • *
  • Posts: 2166
  • Karma: +0/-0
  • Gender: Male
    • View Profile
RE: have you hugged your drill press today
« Reply #197 on: February 20, 2010 3:50 am »
1 inch wire brush
Logged
WANTED: Mel Tillis valve covers

Offline Eyeball

  • Moderator
  • Traditionalist...or...I post to much.
  • *
  • Posts: 6865
  • Karma: +2/-0
  • Gender: Male
    • View Profile
RE: have you hugged your drill press today
« Reply #198 on: February 20, 2010 6:09 am »
Looks great Ross.....pull that tape and let's see what ya got.
Logged
soaken wet shoes and winkled fingers...
hours and hours
inch at a time...

henryj1951 HAMB

Offline sko_ford

  • Suedes Member
  • Traditionalist...or...I post to much.
  • *
  • Posts: 2166
  • Karma: +0/-0
  • Gender: Male
    • View Profile
RE: have you hugged your drill press today
« Reply #199 on: February 20, 2010 3:47 pm »
i plan to today. i'm a little nervous
Logged
WANTED: Mel Tillis valve covers

Offline 31Rodder

  • Suedes Member
  • Traditionalist...or...I post to much.
  • *
  • Posts: 3273
  • Karma: +2/-0
    • View Profile
    • http://geocities.com/rodder1931
RE: have you hugged your drill press today
« Reply #200 on: February 20, 2010 3:59 pm »
can you explain the process Ross, what is the purpose of the tape?

ross i saw this on the hamb.  this could be you.
Logged

Offline sko_ford

  • Suedes Member
  • Traditionalist...or...I post to much.
  • *
  • Posts: 2166
  • Karma: +0/-0
  • Gender: Male
    • View Profile
tape
« Reply #201 on: February 21, 2010 6:45 am »
the tape is not part of the turning process it was put on so i didnt mar the freshly surfaced face of the dash while i broke the bottom edge and rolled the top one.

as for the turning that was easy. 1 inch wire brush lapping each brush mark by half then moving my guide by a 1/2 inch thusly lapping it by half again and stagering each row so they didnt line straight up
Logged
WANTED: Mel Tillis valve covers

Offline sixinarow

  • Suedes Member
  • Hot Rodder
  • *
  • Posts: 795
  • Karma: +1/-0
  • Gender: Male
    • View Profile
sko_ford's A mod
« Reply #202 on: February 21, 2010 3:59 pm »
Here's a working shot. Ross also taped the wire brush so that the size stayed consistent.
Logged
"If you can't fix it with a hammer, it must be an electrical problem."

"Such a fine line between clever and stupid."

Offline sko_ford

  • Suedes Member
  • Traditionalist...or...I post to much.
  • *
  • Posts: 2166
  • Karma: +0/-0
  • Gender: Male
    • View Profile
sko_ford's A mod
« Reply #203 on: February 21, 2010 4:30 pm »
if i were to do it again i would usea hose clamp on the brush insted of tape to keep it to size
Logged
WANTED: Mel Tillis valve covers

Offline sixinarow

  • Suedes Member
  • Hot Rodder
  • *
  • Posts: 795
  • Karma: +1/-0
  • Gender: Male
    • View Profile
sko_ford's A mod
« Reply #204 on: February 21, 2010 4:49 pm »
I was thinking about a hose clamp but was wondering if the screw would throw off the spinning of the brush.
Logged
"If you can't fix it with a hammer, it must be an electrical problem."

"Such a fine line between clever and stupid."

Offline sko_ford

  • Suedes Member
  • Traditionalist...or...I post to much.
  • *
  • Posts: 2166
  • Karma: +0/-0
  • Gender: Male
    • View Profile
sko_ford's A mod
« Reply #205 on: February 21, 2010 5:32 pm »
it was only spinning at 200 rpm so i dont think it would be a deal breaker.
Logged
WANTED: Mel Tillis valve covers

Offline Tom

  • Traditionalist...or...I post to much.
  • *
  • Posts: 3436
  • Karma: +1/-0
    • View Profile
Re: RE: have you hugged your drill press today
« Reply #206 on: February 22, 2010 1:20 pm »
Quote from: "sko_ford"
1 inch wire brush


Did you do it dry?? no lube??
Logged
"A rat rod is a hot rod with poor workmanship". Roger S.

Offline sko_ford

  • Suedes Member
  • Traditionalist...or...I post to much.
  • *
  • Posts: 2166
  • Karma: +0/-0
  • Gender: Male
    • View Profile
sko_ford's A mod
« Reply #207 on: February 23, 2010 1:12 am »
yep dry, there are some imperfections in some of the turns due to some buildup in the brush but i like it and and now fro the fasinating part brass machine screws 10 of em with a 3/8/of an inch head
Logged
WANTED: Mel Tillis valve covers

Offline sko_ford

  • Suedes Member
  • Traditionalist...or...I post to much.
  • *
  • Posts: 2166
  • Karma: +0/-0
  • Gender: Male
    • View Profile
sko_ford's A mod
« Reply #208 on: May 22, 2010 1:33 pm »
headers are almost done. Mud is on. Almost time to cypher on paint
Logged
WANTED: Mel Tillis valve covers

Offline AntiBling

  • Retired Suedes Member
  • Traditionalist...or...I post to much.
  • *
  • Posts: 1090
  • Karma: +0/-0
    • View Profile
    • http://antibling.deviantart.com
sko_ford's A mod
« Reply #209 on: June 07, 2010 2:25 am »
Logged
Pages: 1 ... 12 13 [14] 15 16 ... 20   Go Up
« previous next »